--> A Petrophysical Method to Evaluate Irregularly Gas Saturated Tight Sands Which Have Variable Matrix Properties and Uncertain Water Salinities,by Michael Holmes, Dominic Holmes, Antony Holmes, #40673 (2011)
[First Hit]

Datapages, Inc.Print this page

 Click to view article in PDF format.

 

 

A Petrophysical Method to Evaluate Irregularly Gas Saturated Tight Sands Which Have Variable Matrix Properties and Uncertain Water Salinities*

 

Michael Holmes1, Dominic Holmes1, and Antony Holmes1

 

Search and Discovery Article #40673 (2011)

Posted January 11, 2011

 

*Adapted from oral presentation at AAPG International Conference and Exhibition, Calgary, Alberta, Canada, September 12-15, 2010

 

1Digital Formation, Denver, Colorado ([email protected])

 

Abstract

 

A problem in many Rocky Mountain tight gas sandstones is a Previous HitsequenceNext Hit that is only partially gas saturated, with changing matrix properties combined with variable (and often unpredictable) water salinities. Often it is difficult to distinguish between high resistivity fresh water wet sands, and high resistivity, gas-bearing sands. A standard approach is to make a qualitative judgment based on density/neutron response – the gas “cross-over” effect. However, if matrix properties are variable, this approach can be misleading, and is at best a qualitative judgment.

 

The methodology presented here is a quantitative assessment of gas saturation by comparing matrix specific density and neutron responses with porosity, calculated such that gas effects are minimized. Cross plot porosity from density/neutron combination is only minimally affected by gas and by changing matrix properties.

 

Three sets of calculations are made assuming sandstone (bulk density 2.65 gm/cc), calcareous sandstone (bulk density 2.68 gm/cc) and heavily cemented calcareous sandstone, or limestone (bulk density 2.71 gm/cc). Quantified estimates of gas saturation, as “seen” by each Previous HitlogNext Hit, are available for each assumed rock type. Pressure effects on porosity Previous HitlogNext Hit responses are included in the calculations.

 

Four sets of saturation profiles are now available, one from standard resistivity Previous HitlogNext Hit Previous HitanalysisNext Hit and three from porosity Previous HitlogNext Hit Previous HitanalysisNext Hit assuming different matrix properties. Comparisons among the 4 sets of saturation profiles can be combined with other data, such as mud Previous HitlogNext Hit shows and (if available) core measured matrix densities. Using such comparisons, it is often relatively simple to distinguish between wet intervals and gas-bearing intervals. With increasing assumed grain density, gas saturations calculated from the porosity logs increase. If gas saturations so defined are unrealistically high, it is an indication that actual grain density is less than assumed grain density.

 

Additionally, if matrix properties are Previous HitwellNext Hit-defined, it is possible to verify Rw input for resistivity Previous HitlogNext Hit interpretation, and adjust as necessary. It is important to recognize that the porosity logs, and particularly the density Previous HitlogNext Hit, investigate close to the wellbore, and may Previous HitwellNext Hit be influenced entirely by the flushed zone. Examples are presented from Rocky Mountain reservoirs, in sequences where the problem of irregular gas saturation in systems with variable Rw is particularly severe.

 

Figures

 

Copyright � AAPG. Serial rights given by author. For all other rights contact author directly.

 

Abstract
Figures
Methodology
Example




















Abstract
Figures
Methodology
Example


















Abstract
Figures
Methodology
Example


















Abstract
Figures
Methodology
Example


















Abstract
Figures
Methodology
Example


















Abstract
Figures
Methodology
Example


















Abstract
Figures
Methodology
Example


















Abstract
Figures
Methodology
Example


















 

 

fig01

Figure 1. Schematic of gas saturation from porosity Previous HitlogNext Hit Previous HitanalysisNext Hit (for shallow reservoirs).

fig02

Figure 2. Depth Previous HitlogNext Hit from standard shaley formation resistivity Previous HitanalysisNext Hit. Track descriptions are as follows: (1) raw wireline Previous HitlogNext Hit; (2) reservoir composition, where yellow indicates matrix, red indicates porosity, and grey indicates shale; (3) water saturation, core data illustrated by blue and green symbols; (4) bulk volumes where grey indicates shale, brown indicates hydrocarbons, light blue indicates poor quality reservoir (possible mobile water), and dark blue indicates capillary bound water; (5) pay flags where yellow indicates gross reservoir, red indicates net reservoir, and green indicates net pay.

fig03

Figure 3. Interpretation of porosity vs. resistivity relations to determine parameters for Archie Previous HitanalysisNext Hit. a (cementation constant) = 1.0, Rw (water resistivity) = 0.1, m (cementation exponent) = 2, and n (saturation exponent) = 1.7.

fig04

Figure 4. Depth Previous HitlogNext Hit showing gas saturation from porosity Previous HitlogNext Hit Previous HitanalysisNext Hit. Track descriptions are as follows: (1) reservoir composition, where yellow indicates matrix, red indicates porosity, and grey indicates shale; (2) water saturation, core data illustrated by blue and green symbols; (3) bulk volumes, where grey indicates shale, brown indicates hydrocarbons, light blue indicates poor quality reservoir (possible mobile water), and dark blue indicates capillary bound water; (4) matrix properties - grain density and matrix travel time; (5) permeability, core data illustrated by black symbols. Tracks 6, 7, and 8 show porosity and gas saturation from porosity logs only. Yellow indicates gas saturation from porosity logs, and blue indicates water saturation from resistivity Previous HitlogNext Hit Previous HitanalysisNext Hit. Track 6 shows Previous HitanalysisNext Hit assuming a grain density of 2.65 gm/cc, track 7 shows Previous HitanalysisNext Hit assuming 2.68 gm/cc, and track 8 shows Previous HitanalysisNext Hit assuming a grain density of 2.71 gm/cc. Track 9 contains pay flags where yellow indicates gross reservoir, red indicates net reservoir, and green indicates net pay. 9a shows pay flags from resistivity Previous HitanalysisNext Hit, 9b shows pay flags from porosity Previous HitlogNext Hit Previous HitanalysisNext Hit assuming grain density of 2.65 gm/cc, 9c shows pay flags from porosity Previous HitlogNext Hit Previous HitanalysisNext Hit assuming grain density of 2.68 gm/cc, and 9d shows pay flags from porosity Previous HitlogNext Hit Previous HitanalysisNext Hit assuming grain density of 2.71 gm/cc.

 

Methodology

 

Shaley Formation Resistivity Previous HitAnalysisNext Hit

 

The interpretation is a standard shaley formation Previous HitanalysisNext Hit, involving calculations of total porosity, shale volume, and total water saturation. One of the issues in tight gas sands is the correct choice of matrix lithology. If only a density Previous HitlogNext Hit is used, the correct choice of grain density is crucial. In the event of lack of core data this may be particularly problematic, especially if grain density is variable. By using a density/neutron cross plot, this restriction is overcome. Fluid density is a required input, and should be estimated from a reasonable assumption of gas saturation close to the wellbore. A porosity/resistivity cross plot can help in this choice.

 

The second set of Previous HitanalysisNext Hit involves the calculation of effective porosity and water saturation (i.e. removing the effects of clay). From these calculations, again based on resistivity interpretations, potential mobile water and/or poor quality reservoir rock can be distinguished from capillary bound water. Lack of light blue color fill on Figure 2, track 4 and Figure 4, track 3 equates to better quality, gas-bearing reservoirs. Example of application of these techniques are described in AAPG Annual Convention, June 2009 “Relationship Between Porosity and Water Saturation: Methodology to Distinguish Mobile from Capillary Bound Water ” by Michael Holmes, Antony Holmes, Dominic Holmes.

 

Gas Saturation from Porosity Logs

 

Comparison of density with neutron logs is used routinely for a qualitative assessment of the presence of gas – the density/neutron “cross-over” effect. The response is controlled by the concentration of hydrogen in the pore space. Because gas contains less hydrogen than oil or water, apparent neutron porosity is suppressed. The cross plot (Figure 1) shows the effects of gas. Porosity values are lithology specific, i.e. raw logging data must be converted to a known (or presumed) lithology. By assuming different lithologies, the cross plot can be solved for gas saturation. The assumption is made that the density and neutron logs both investigate about the same volume of rock – or, as in the case of tight gas sands, there is a little variation of gas saturation away from the wellbore (minimal or no invasion by drilling fluid). Three different lithologies are assumed in this paper:

 

 

 

Example

 

Standard resistivity interpretation from a Piceance Basin Previous HitwellNext Hit, NW Colorado, is shown in Figure 2. Interpretation of the porosity resistivity cross plot (Figure 3) shows input used for saturation determination:

 

Rw = 0.1 Water resistivity

a = 1.0 Cementation constant

m = 2.0 Cementation exponent

n = 1.7 Saturation exponent

 

A summary of the interpretation is as follows:

  • Sands from 4850-5000 ft are either tight (as at 4890-4910 ft) or wet (as at 4920-4940 ft).
  • From 5000-5140 ft the sands are routinely gas bearing and, for tight sands, fair reservoir quality – average core permeability 0.1 mD or above.
  • From 5140-5200 ft, the sands are tight – average core permeability less than 0.01 mD.

 

Figure 4 shows the same interval as Figure 2, with the addition of interpretations of gas saturation from porosity logs. Examination of the porosity Previous HitlogTop Sg data shows the following:

  • None of the sands has a grain density of 2.71 gm/cc (calculations assuming this value show unrealistically high gas saturations).
  • The shallower sands (above 5000 ft) appear to be mostly wet, with a grain density of 2.65 gm/cc - or they are gas bearing with a more saline water (lower Rw) than the shallower sands, with a grain density of 2.68. Core measured grain densities would help solve the problem.
  • Sands from 5000-5140 ft are gas bearing with a grain density of 2.68 gm/cc.
  • Sands below 5140 ft are not gas bearing, regardless of assumed grain density.

 

Return to top.