[First Hit]

Datapages, Inc.Print this page

 Click to view article in PDF format.

 

 

GCThin-Bed Interpretation Using Reference Surfaces*

 

Bob Hardage1

 

Search and Discovery Article #40535 (2010)

Posted May 31, 2010

 

*Adapted from the Geophysical Corner column, prepared by the author, in AAPG Explorer, May, 2010, and entitled “Looking High and Low for References”. Editor of Geophysical Corner is Bob A. Hardage (mailto:[email protected]). Managing Editor of AAPG Explorer is Vern Stefanic; Larry Nation is Communications Director.

 

1Bureau of Economic Geology, The University of Texas at Austin ([email protected])

 

 

General Statement

 

The fundamental criteria required of a Previous HitseismicNext Hit reflection event that is to be used as a reference surface for interpreting thin-bed geology are that the Previous HitseismicNext Hit reflection should:

 

1) Extend across the entire Previous HitseismicNext Hit image space and have a good signal-to-noise character.

 

2) Be reasonably close (vertically) to the geology that is to be interpreted.

 

3) Be conformable to the strata that need to be analyzed.

 

Criterion 3 is probably the most important requirement on this list.

 

Figures


General statement
Figures
Example
Conclusion




















General statement
Figures
Example
Conclusion




















General statement
Figures
Example
Conclusion




















General statement
Figures
Example
Conclusion













fig01

Figure 1. Previous HitVerticalNext Hit slices through a 3-D Previous HitseismicNext Hit volume showing a targeted channel system (a), and horizon slices A, B, C and D which cut through the channel window (b). These four horizon surfaces are approximations to stratal surfaces because they are conformable to the indicated reference surface, which is a chronostratigraphic reflection event. This profile is labeled 200 on Figure 2.

fig02

Figure 2. (a) Reflection amplitude across Previous HitseismicNext Hit image space on horizon B (Figure 1b); (b) Reflection amplitude across Previous HitseismicNext Hit image space on a horizon 26 meters below reference surface 2 (Figure 3, below).

fig03

Figure 3. Previous HitSeismicNext Hit profile 222 shown on Figure 2. Reference surface 1 is the surface defined on profile 200 (Figure 1) below the channel target. Reference surface 2 is a second choice for a reference surface located above the channel that can be used to construct horizon slices that cut through the targeted channel complex.

 

Example

 

Figure 1 shows a data window from a Previous HitverticalNext Hit slice through a 3-D Previous HitseismicNext Hit volume  centered on a channel system that is to be interpreted. The Previous HitseismicNext Hit reflection event labeled “reference surface” was selected as an appropriate conformable reflection for interpreting the thin-bed channel system identified on Figure 1a. The reference surface in this case follows the peak of the Previous HitseismicNext Hit reflection event on which it is positioned.

 

Four horizon surfaces labeled A, B, C and D, each conformable to the reference surface, pass through the targeted channel system on Figure 1b. Each of these horizon surfaces can tentatively be assumed to be a reasonable approximation of a stratal surface that intersects the channel system because each horizon is conformable to the selected reference reflection event, and a fundamental thesis of Previous HitseismicNext Hit stratigraphy is that Previous HitseismicNext Hit reflection events are chronostratigraphic by definition.

 

Figure 2a shows reflection amplitude behavior on horizon surface B. This horizon surface does a reasonable job of defining the targeted channel system (channel 1) across the lower right quadrant of the display and also depicts a second channel system (channel 2) at the top of the image display. The image on Figure 2a is a horizon-based image, meaning that the Previous HitseismicNext Hit attribute that is displayed is limited to a data window that vertically spans only one data point.

 

In challenging interpretation problems, it is important to try to define two Previous HitseismicNext Hit reference surfaces that bracket the geological interval that is to be interpreted – one reference surface being below the geological target and the other being above the target. An interpreter can then extend conformable surfaces across a targeted interval from two directions (from above and from below). Sometimes one set of conformable surfaces will be more valuable as stratal surfaces than the other at the level of a targeted thin bed.

 

To illustrate the advantage of this opposite-direction convergence of Previous HitseismicTop horizon surfaces, a second reference surface was interpreted above the targeted channel system and was placed closer to the target interval. This second reference surface followed the apex of the reflection troughs immediately above the channel system. The two bracketing reference surfaces are shown on Figure 3.

 

The reflection amplitude response on a horizon surface conformable to reference surface 2 and positioned 26 milliseconds below that reference surface is displayed on Figure 2b. This image is again a one-point-thick attribute display (i.e. a horizon-based attribute). The channel systems are a bit crisper in appearance and their geometries are more definitive on this second imaging attempt than they were on the first effort (Figure 2a).

 

Conclusion

 

This dual-direction approach to constructing horizon surfaces that traverse thin-bed targets is a concept that often will provide valuable results. An even better approach would be to calculate stratal slices through a bracketed data window – a concept discussed and illustrated in the Geophysical Corner article published June 2006 (http://www.searchanddiscovery.net/documents/2006/06036zeng_gc/index.htm).

 

Unfortunately, not all interpretation software provides a stratal slicing option. In those cases, a dual-direction-approach strategy such as described here can be valuable for constructing horizon slices that approximate stratal slices.

 

Return to top.

 

Copyright © AAPG. Serial rights given by author. For all other rights contact author directly.