Click to view article in PDF format.
PSWest Athabasca Grand Rapids Formation – A New SAGD Play*
M.E. Connelly1 and Laurie M. Weston Bellman1
Search and Discovery Article #10282 (2010)
Posted November 30, 2010
*Adapted from oral presentation at AAPG International Conference and Exhibition, Calgary, Alberta, Canada, September 12-15, 2010
1Laricina Energy Ltd. & L.M. Weston Bellman (Oil Sands Imaging) ([email protected]), ([email protected])
The majority of Steam-Assisted Gravity Drainage (SAGD) development to date has been concentrated in the Cretaceous McMurray Formation in the Eastern Athabasca fairway of the oil sands deposits of northeastern Alberta, Canada. More recently, operators have identified projects with considerable resource located in shoreface sands of the younger Cretaceous Grand Rapids Formation further west in the Wabasca area (Figure 1).
The Grand Rapids Formation comprises the upper part of the regressive Upper Manville Group (Cant et al., 1997) and consists of multiple thick sandstones hosting 54.5 billion barrels (8678 x 106 m3) of bitumen in place (ERCB, 2009). The uppermost Grand Rapids sand is the largest of the three identified deposits with 33.2 billion barrels (5274 x 106 m3) in place (EUB, 1996). Much of the bitumen resource is underlain by a thin bottom water leg of varying thickness (Peterson et al., 2008).
The complex estuarine depositional environment in which the McMurray sands were deposited resulted in heterogeneous and complex reservoirs. In contrast, the upper Grand Rapids sand is interpreted to have been deposited in a regional marine shoreface setting. Its unique features – broad deposition, clean sand with homogeneous and continuous reservoir pay – increase the predictability and consistency of the reservoir. Laricina Energy Ltd. (Laricina) holds a total of 63 sections (the Germain lease) in the fairway with an estimated 2.5 billion barrels (0.4 x 106 m3) of bitumen in place. Laricina has filed applications for regulatory approval of a commercial demonstration project capable of producing 5000 bbl/day utilizing a variant of SAGD technology which is based on steam and solvents (Figure 2).
In conventional SAGD reservoirs, the horizontal production and injection well pairs are typically placed within the bitumen zone. However, based on laboratory and new simulation studies, Laricina has determined that bitumen recovery in a reservoir with thin associated basal water can be maximized by placing the producer at the base of porosity within the basal water zone (Peterson et al., 2008 and Peterson et al., 2009). The key aspects and concerns in the SAGD development of the Grand Rapids bitumen resource include clearly identifying the porosity base, the bitumen-water contact and any impedance to vertical permeability. To address these issues, a detailed 3D reservoir characterization was required. This presentation will describe the process of integrating core, log and 3D seismic data in the Germain lease to produce a volume of deterministically derived lithology and fluids within the reservoir.
|
The upper Grand Rapids sand has been a focus of recent drilling and seismic acquisition by Laricina in the Germain lease (T84 R22 W4). Wireline logs and core photos of a type well from the lease is shown in Figure 3. Unlike typical McMurray reservoirs, the upper Grand Rapids sand is homogenous with very rare muddy interbeds. However, the reservoir parameters are similar to the McMurray with bitumen thickness ranging from 10 to 25 meters, average porosity of 34%, bitumen saturations ranging between 65 and 75% and permeability ranging between 1 and 5 Darcy.
Due to the simple nature of this reservoir, a fairly simple set of facies descriptions were established and identified from core. The facies identified were bitumen sand, wet sand, shaley sand, sandy shale, shale and dense or cemented sands. The wet sand facies occurs at the base of the upper Grand Rapids sand, at the base of the bitumen sand interval. Typically, the shale facies are only found above the bitumen sand and below the basal water sand as bounding shales to the sand deposit. Occasional dense or cemented intervals are present within the reservoir sand. These zones are generally very thin, less than 0.5 meters thick and do not correlate between wells. Core and outcrop data suggest that these are limited in areal extent as lateral termination has been encountered in core and these zones are limited to only a few meters in length in outcrop (Figure 4).
The core facies interpretations were then integrated with the wireline log data for the 3D reservoir characterization analysis. Wireline logs directly (or indirectly) measure P-
The seismic process involves the use of AVO (amplitude vs offset) analysis to separate the compressional (P-
The resulting 3D visualization of the lithology and fluid distribution clearly identifies the porosity base of the sand and the bitumen-water contact. This will allow for confident placement of the horizontal well pairs for the SAGD process with the producer placed just above the base of porosity and the injector just above the bitumen-water contact (Peterson et al., 2009). The thin dense sands within the reservoir interval are not able to be resolved in this dataset, however thicker ones such as those in the lower Grand Rapids sand are apparent.
Integration of core, log and seismic data allow for greater understanding of even simple reservoirs like the Grand Rapids. Identifying the presence and location of barriers to vertical permeability, the base of porosity and bottom water thickness allows Laricina geologists and engineers to make decisions regarding important SAGD issues with respect to reservoir development and provides greater confidence in locating horizontal wells in the reservoir.
We would like to thank the management at Laricina Energy Ltd. for allowing us to release this information.
Cant, D.J. and B. Abrahamson, 1997, Regional stratigraphy, sedimentology, and petroleum geology of the Grand Rapids Formation, Mannville Group, Northeastern Alberta, Bulletin of Canadian Petroleum Geology, v. 45, p. 141-154.
EUB Report ST96-38, 1996, Crude Bitumen Reserves Atlas, May.
ERCB Report ST98-2009, Alberta’s Energy Reserves 2008 and Supply/Demand Outlook 2009-2018
Goodway, W., T. Chen, and J. Downton, 1997, Improved AVO fluid detection and lithology discrimination using Lame petrophysical parameters; “Lambda*rho”, “mu*rho” and “lambda/mu fluid stack”, from P and S inversions, 67th Annual International Meeting, SEG Expanded Abstracts, p. 183-186.
Peterson, J.A., M.E. Connelly, and N.R. Edmunds, 2008, Bitumen Production
Peterson, J.A., D.T. Riva, M.E. Connelly, S.C. Solankiand, and N.R. Edmunds, 2009, Conducting SAGD in Shoreface Oil Sands with Associated Basal Water, Canadian International Petroleum Conference, June 16-18, Paper 2009-128, 12 p.
Russell, B., D. Hampson, J. Schuelke, and J. Quirein, 1997, Multi-attribute Seismic Analysis, The Leading Edge, October, p. 1439.
Copyright © AAPG. Serial rights given by author. For all other rights contact author directly. |