Click to view article in PDF format.
PSExamining Detailed Facies and Rock Property Variation in Upper Cretaceous, Tight Gas Reservoirs, Pinedale Field, Wyoming*
Mark A. Chapin1, Andrew Govert1 and Gustavo Ugueto1
Search and Discovery Article #20077 (2009)
Posted September 17, 2009
*Adapted from poster presentation at AAPG Convention, Denver, Colorado, June 7-10, 2009
1Shell, Denver, CO ([email protected])
The giant Pinedale gas field is located in the northern Green River Basin, Wyoming (Figure 1). Gas is produced from ~5500 ft (1675 m) of Upper Cretaceous fluvial sandstones of the Lance Formation, Upper Mesaverde Group, and the Paleocene “Unnamed” unit – collectively known as the “Lance Pool”. The reservoir is classified as tight gas, with sandstone porosity generally <10% and with micro-Darcy permeability. Over 4000 feet (1220 m) of core have been examined to better characterize facies for correlation to rock properties. These detailed facies and rock property relationships have been incorporated into reservoir models to influence development decisions on down-spacing and completion intervals.
Two main types of reservoir sandstones include river channel deposits and overbank crevasse splay sands. Channel sands display classic fining-up sequences (Figure 2). These sequences have been sub-divided into four facies: (1) channel base lags - “Cl”, (2) basal bar or active channel fill - “Ca”, (3) upper bar or partial abandonment fill - “Cb”, and (4) soil-modified bar top - “Cu”. Characteristics of these facies are described in more detail in Figure 2 and Figure 3. Splay sandstones are typically very-fine grained and highly cemented, with lower reservoir quality.
Despite an overall similarity in fluvial facies character, there are variations in sand percent, stacking pattern and overbank environments both vertically and laterally around the anticline (Figure 4). Overbank mudstones and siltstones contain many indications of soil formation, e.g. rooted zones, granular, crumb and blocky peds, caliche nodules, zones of calcite enrichment and depletion, and lack of undisrupted lamination. Rooting and ped structures are ubiquitous. However, other mudrock features vary in their abundance in the vertical section, providing clues to overall environment (Figure 4 and Figure 5).
The lower, “Mesaverde”
interval has less sand percent, thinner channel sands, thicker intervals of splay sands, and overbank mudstones that are more carbonaceous and bioturbated. This
suggests a higher-accommodation, lower coastal plain setting with poorly drained floodplains. The Lance Formation contains thicker channel deposits
with varying amalgamation. Especially prominent is the gradation from thick, amalgamated “Middle Lance” sandstones in the north, to mud-dominated Middle
Lance towards the south. Lance Formation overbank muds range from more carbonaceous at the base, to more oxidized (presence of red and red-green mottling)
with common caliche nodules at the top indicating transition from poorly to well
-drained flood-plains. The Unnamed Formation channel deposits contain
arkosic gravel bars, indicating exposure of the granitic core of the Wind River Range, as indicated by Law and Spencer (1989).
Despite significant compaction and cementation leading to low porosity and permeability, we can demonstrate
good correspondence of core and log
petrophysical properties to facies (Figure 6
and Figure
7). Detailed core examination can explain many features on logs. Figure 6
shows how mud clast lags have high gamma ray and low resistivity, but the matrix sandstone between the mud clasts can
have very good permeability (Figure 7). We created continuous calcite reaction logs
during core description by indicating how vigorously the core reacted with HCL drops. The low porosity zone at 9365 ft in Figure
6
can be seen to correspond
with higher acid reactivity, indicating a higher proportion of carbonate cement. These core observations have been confirmed via XRD and petrographic
analysis
. The correspondence of core porosity to
log
-derived porosity in Figure 6
is very good. The correspondence of core permeability to
log
-derived permeability (from poro-perm cross-plot regression)
is more variable, but the trends are
well
captured.
There is a good correspondence of stress-corrected log10 permeability to porosity within sandstones, and it is clear that porosity is the main contributor to permeability at the core scale (Figure 7). In addition, facies identification can provide sub-classes for rock-property modeling – with larger grain size and higher energy facies having generally greater porosity and permeability.
Investigations of story thickness, stratification types and rock properties in single-story and multi-story channels have provided guidelines for populating detailed reservoir models for performance prediction. In general multi-story and single story channel sequences have similar facies – with the significant exception that channel lags are very rare in single-story channels. Multi-story channels have a lesser proportion of preserved Cb and Cu facies, due to erosion and amalgamation. Porosity and permeability within facies classes are similar between single and multi-story channels.