Click to view posters in PDF format.
Poster 1 (2.3 mb) Poster 2 (0.5 mb) Poster 3 (0.5 mb)
Poster 4 (2.7 mb) Poster 5 (0.4 mb)
Right click on poster to save.
PSPrediction
of Sub-seismic
Sealing Faults Using Simple Numerical Simulation Models*
By
R.C. Bain1, K.H. MacIvor1, B.E. Holt1, and D.S. Beaty1
Search and Discovery Article #40242
Posted May 28, 2007
*Adapted from poster presentation at AAPG Annual Convention, Long Beach, California, April 1-4, 2007
1Chevron North America Upstream, Houston, Texas ([email protected])
In order to
justify development drilling in a partly-depleted, highly faulted gas reservoir
in which untapped higher-pressure compartments may exist, convincing evidence
for fault separation from existing producing wells must be provided, either by
obvious fault breaks on 3-D seismic
or by missing section due to a fault
encountered in a well. Lacking such evidence, it is difficult to state with
certainty that prospect reserves will be incremental, as opposed to
acceleration, even when volumetric analysis suggests that existing wells will
not capture all of the producible reserves in a reservoir.
The Mid-Continent Business Unit of Chevron North America Exploration and
Production has had success in the Lobo Trend of Webb and Zapata Counties, South
Texas, using simple, "fit-for-purpose" 3D-earth models and numerical simulation
models that provide a level of confidence sufficient to predict the location and
expected reservoir conditions of remaining incremental reserves in a
partly-developed reservoir. These models have proven to be very useful in their
ability to provide quick results with limited geologic and reservoir data
. The
key factor in their success is the proper integration of flowing pressure
data
with observed production decline curves. Static reservoir pressure measurements
are typically unavailable and also give misleading results when used for P/Z
volumetric analysis in compartmentalized reservoirs.
In the first example, a simple simulation model predicted the presence of
sub-seismic
faulting that provided a seal for the objective reservoir. The
proposed location was in a syncline between two wells that had already produced
large volumes of gas and were producing at very low bottom-hole pressures. An
iterative approach involving the
seismic
interpreter and the reservoir engineer
resulted in a geologic model that was supported by the
seismic
data
and agreed
with the history matching efforts. The well, which would not have been approved
without the model to support it, encountered near-virgin reservoir conditions.
The second example provides a lesson learned, demonstrating a reservoir in which the reservoir simulation and history match correctly predicted the presence of a sealing fault, but incorrectly predicted which of several faults was the sealing one. The sealing fault was penetrated by the wellbore and the seal was ruptured when the well was fracture stimulated.
Quickly
demonstrating the accuracy and applicability of simple numerical models in an
environment where rig moves are rapid and reservoir data
is sparse has generated
a new interest in a tool that was heretofore thought too complex and too time
consuming to apply. Asset Team Earth Scientists are now working more closely
with the reservoir simulation engineers and are using the results from these
simple models to help in their
interpretation
of subsurface geology, especially
in highly faulted environments. In some cases, successful wells are being
drilled where they otherwise would not have been.
|
Poster 1: The Problem, Geologic Setting, and Reservoir Simulation Basics Volumetric calculations indicate that two wells producing from the same gas reservoir have not drained all of the producible reserves in a 200-acre fault block. The challenge is to identify economic drill locations despite the fact that the existing wells appear to be depleted.
Posters 2 and 3: Case Study #1 A 3-D
By
interpreting tiny offsets of flexures in
Poster 4: Case Study #2 In a different part of the model created in Case Study #1, a well was proposed to offset a competitive drainage situation in a 60-acre fault block. The proposed well was expected to encounter similar pressure to a recently drilled updip well. An unexpected 80-foot fault was encountered in the objective reservoir when the well was drilled, but the pressure matched what had been predicted by the simulation model. However, after fracture stimulating the well, the observed pressure had decreased by more than 2000 psi. The fault encountered in the well was apparently a seal between two compartments of vastly different pressure. The stimulation ruptured the seal and the frac job “went south.”
Flowing tubing pressure (converted to bottom hole flowing pressure) can be used for the pressure match when other reservoir pressure measurements are unavailable |