Click
to view article in PDF format.
GCStratal Slicing Makes Seismic Imaging of Depositional Systems Easier
By
Hongliu Zeng1
Search and Discovery Article #40196 (2006)
Posted June 4, 2006
*Adapted from the Geophysical Corner column, prepared by the author and entitled “Seismic Imaging? Try Stratal Slicing,” in AAPG Explorer, June, 2006. Editor of Geophysical Corner is Bob A. Hardage. Managing Editor of AAPG Explorer is Vern Stefanic; Larry Nation is Communications Director.
1Research scientist, Bureau of Economic Geology, University of Texas, Austin, Texas ([email protected])
Many people today view land surfaces from commercial airplanes or on satellite images and are amazed by the geomorphic forms of river channels, deltas, barrier islands, dune fields, and other features. These views show us modern stratal-time surfaces of exposed landforms.
Three-D seismic technology has now made it possible to image similar, but much older, geomorphic features and stratal surfaces preserved in the rock record. Historically, interpreters have analyzed vertical sections of 3-D seismic volumes line by line and found field-scale (50 meters or thicker) geologic and depositional features. Sometimes, reservoir-scale (three-10 meters thick) features can be detected in these vertical sections, but many of these small-scale targets cannot be resolved and interpreted because of data bandwidth limitations.
For example, in the vertical view in Figure 1a the seismic facies around the dash line are interpreted to be fluvial deposits, based on the presence of discontinuous, patchy events and frequent lateral changes in amplitudes. Wells drilled through the interval support this interpretation.
However, correlating individual channel-fill sand bodies and marginal facies (levee, crevasse splay, etc.) on adjacent vertical views is difficult because these facies elements are thin (three-10 meters) and the seismic resolution barely resolves the tops and bases of the thickest units. In this particular section view, it is not possible to decide what depositional elements are represented by the circled features.
uGeneral statementuFigure captionsuSlicesuStratal slicinguAppendix
uGeneral statementuFigure captionsuSlicesuStratal slicinguAppendix
uGeneral statementuFigure captionsuSlicesuStratal slicinguAppendix
|
Time, Horizontal, and Stratal Slices One strategy to map depositional systems with high resolution is to change the emphasis of seismic interpretation from vertical sections to horizontal sections. For a perfectly migrated 3-D seismic data set, horizontal resolution is the same as vertical resolution. Outcrop and subsurface studies show depositional bodies have horizontal dimensions greater than their vertical dimensions. As a result, small depositional bodies often can be resolved in plan view even if they can only be detected in vertical view. As a demonstration of this principle, a stratal slice made by the method described in this article and then passed through the dash line in Figure 1a shows high-quality images of fluvial channels, crevasse splays, floodplain, and a mud plug (Figure 1b). Although most of these depositional elements are less than 10 meters thick -- and thus below vertical seismic resolution -- they are well resolved in the horizontal dimension. To implement
horizontal-view seismic interpretation, we must pick geologic-time
surfaces (or stratal surfaces) from 3-D seismic volumes so that seismic
attribute maps across these fixed-geologic-time surfaces can be analyzed
in terms of depositional systems. Time slices and horizon slices are the
horizontal-section views most commonly used by seismic interpreters (Figures
2a-b). Time slices are extracted from a data volume at a constant
image-time For either horizontal view to be an accurate representation of a stratal surface, one must assume the formation being sliced is flat-lying when time slicing is used (Figure 2a), or that the formation has a sheet-like geometry (Figure 2b) when horizon slicing is used. Many depositional sequences, however, are characterized by thickness changes (Figure 2c), which cause horizon-slice and time-slice surfaces to sample seismic events that are associated with strata of different geologic ages. A different surface extraction method must be used to ensure an extracted surface follows a fixed-geologic-time surface. One such method is
“stratal slicing” (Figure 2c), or
proportional slicing, which divides the variable-thickness vertical
interval between two seismic reference events (Figure
2) into a fixed number of uniformly spaced subintervals. If the
number of subintervals is 10 and the time thickness between the
reference surfaces at points A and B (Figure 2)
is 27 ms and 58 ms, respectively, then the thickness of each subinterval
at In principle, no major angular unconformities (truncations) or other discordant reflections should occur between the reference events.
Stratal slices
provide a stratigraphic resolution that cannot be achieved Four stratal slices were taken inside a 30-ms (36-m) interval (Figure 3, S1 through S4). Interpretation of wireline well logs (SP) across the interval shows the sandstones are fluvial in nature. Some of the sandstone units (e.g., a, b and e in Figure 3) are thick (20 to 25 meters) and create amplitude anomalies. Others are thin (10 meters or less) and subtle (c, d and f in Figure 3). In map view, the four stratal slices image four episodes of fluvial deposition (Figure 4, S1 through S4). The fluvial systems on stratal slices S1, S2, and S4 are fully resolved without interference from overlying or underlying units. Stratal slice S3
shows a narrow (35 to 70 meters, or 1 to 2 traces wide), well-developed
meandering feature interpreted to be a small coastal plain channel (Figure
4, arrows). Wireline logs indicate this channel-fill sandstone is
about four meters thick. Image S3 is only six ms (seven meters) above
slice S2 and is contaminated by some interference from the S2 fluvial
Even so, identification of the meandering channel across stratal surface S3 is unambiguous. The image resolution achieved in this case is much smaller than vertical resolution and probably represents the limit of resolution expected from stratal-slice analysis for this data set.
The software used to make stratal slices, including necessary reconditioning of seismic data and various attribute applications, was developed by a joint effort of academia and industry, and is available at www.austingeo.com. |