Click
to article in PDF format.
Subsurface Fluid Compartments: Report*
By
D. E. Powley1
Search and Discovery Article #60006 (2006)
Posted March 14, 2006
*Adapted from Amoco Geological Research Report, December 30, 1984
1Amoco Production Company, retired, Tulsa, Oklahoma 74136
|
Purpose, Summary, and Introduction The purpose of this report is to summarize progress made over the last few years in understanding the movement of subsurface fluids as interpreted from subsurface fluid pressures. During that time it was recognized that, in most of the deep basins in the world, there are at least two superimposed hydraulic systems. The shallowest hydraulic system generally extends from the surface down to about 9000-12,000 ft greatest historical depth of burial and typically exhibits normal pressures. The deeper hydraulic system generally consists of individual compartments which are sealed off from each other and from the overlying system. The pressures within the compartments in the deep hydraulic system are usually markedly overpressured or underpressured relative to the pressures in the overlying hydraulic system. In some basins there is a deeper, near normally pressured section. This report deals with the geological and exploration implications of fluid compartments. The study was conducted on an informal when-time-is-available basis and draws from experience derived from several limited-objective technical-service-type studies conducted for various Company locations. Also, literature and personal-communication data were collected on about 200 of the world’s nearly 500 basins. Intensive collection and review of data were concentrated on about 70 basins, over half of which are in North America. This report does not attempt to discuss each of those basins; it deals with the summation of observations and conclusions drawn from all of the basins studied. A seminar or slides on the data assembled pertinent to specific basins can be supplied if needed.
Conclusions1. There are so many basins with a layer of fluid compartments that the formation and preservation of compartments appear to be parts of normal basin development. 2. Seals bounding subsurface fluid compartments may trap or localize the entrapment of oil and gas. 3. Recognition and mapping of subsurface compartments mainly on the basis of pressure data are generally relatively easy and can become parts of the normal procedures used in development and assessment of exploration plays.
Prior StudiesThere
have been three periods of innovative interpretations of subsurface
pressures. The first was an amazingly perceptive study of the
relationship of oil and gas pools to water density and water pressures
in sand reservoirs in Rocky Mountains basins conducted in 1924 and 1925
by Clare Coffin, a geologist then with an Amoco predecessor company
(Coffin, 1925). He introduced the concepts and mathematics of tracing
water flow through subsurface formations from entry at high elevation
outcrops to exits at lower elevation outcrops. He correctly pointed out
that, while fresh water entering high outcrops may, on the basis of
elevations of water inlet outcrops and water outlet outcrops alone,
appear to have sufficient head to push heavier salty water from deep
within basins, it actually selects the path of least resistance over the
heavier brines and thus moves within individual permeable rock layers
around the basins in the shallow basin-periphery rocks to lower outcrops
or, in some cases, moves by sheet-like The next period of interest in pressure indicators of underground fluid flow conditions was in the mid 1950’s when King Hubbert (Shell) and William Russell (Texas A&M University), working independently, presented mathematical explanations for the tilted oil/water interfaces observed in a few pools. The explanations involved rapid movement of the water in basal contact with the base of oil columns. Russell (1956) recognized that tilted contacts may be produced by stratigraphic variations; however, that cautionary note was lost in an almost competitive outpouring of literature and talks on tilted oil/water interfaces by those and other authors. Hubbert (1940, 1954), to a greater extent than others, displayed the misconception that each aquifer is independent of all other aquifers and the resultant misconception that aquifers in basins may be likened to U tubes in which fresh water enters at high elevation outcrops and proceeds directly across basins displacing heavy deep-basin brines rather than flowing over or around the brines. Hubbert became a distinguished lecturer for the American Association of Petroleum Geologists on interpretive tracing of water flows by the use of pressure data. He labeled his interpretation technique “hydrodynamics”. His lectures included a movie of an experiment using a large glass U tube with small kinks to represent an aquifer in a basin with anticlines. He flowed water and oil into the apparatus and showed that, by adjustment of flow velocities, (1) he could cause oil to collect at the tops of the upbend kinks, (2) at faster rates the oil would collect on the downflow direction sides of the kinks and (3) at greater water flow rates the oil would be swept out of the tubing along with the water. This demonstration caused a great deal of spectator interest. That interest led to the drilling of several downflank wildcat wells in attempts to find oil pools displaced from structure-crest positions by moving water. These wells were almost universally dry; in fact, this author is unaware of any significant oil or gas pools anywhere in the world which were deliberately found by application of hydrodynamics techniques. The concepts and mathematics have been convincingly used by proponents of the technique in explaining oil/water interface tilts in a few pools which were discovered on the basis of other, more conventional, exploration concepts and techniques. Despite its obvious failure to date as an oil and gas finding technique, Hubbert-type hydrodynamics still bears a charm to some people, probably because of its mathematical elegance. When the pace of drilling revived after the 1957-1965 imports-induced domestic drilling slump, many wells were taken to greater than usual depths. Many of those deeper wells encountered higher-than-anticipated subsurface pressures. In many basins it was recognized that the top of the high pressures does not follow traditional stratigraphic layers, so many geologists’ interests shifted to searches for unusual local factors which might control fluid pressures. There was an ensuing flood of published papers and Company reports which attempted to relate the high pressures to various rock and mineral properties. Colin Barker (1972) and John Bradley (1973, 1975, 1976) broke the stream of rock and mineral properties-pressures relationship papers by resurrecting an old concept (Versluys, 1932; Illing 1938) that the expansion of water when heated exceeded the expansion of rock pores and they pointed out that thermal expansion and thermal contraction of confined pore waters resultant from changes in subsurface temperatures during progressive basin filling and subsequent progressive erosion satisfactorily accounted for most of the abnormal pressures being encountered in wells worldwide. Rock and mineral properties induced pressure effects, such as compaction, clay minerals changes and osmotic membranes, were left with a minimally important, contributory role in generation of pore pressures. Studies of pressures were generally terminated at this point. During the late 1960’s and 1970’s, simultaneously with the interest in the origin of abnormal pressures, geochemists were collecting data and developing concepts which placed the depth of thermochemical generation of petroleum in the general 10,000 to 16,000 ft range in low-in-kerogen-associated-sulfur rocks in many basins. That depth range places the generation of much oil and gas within or, in a few basins, below abnormally pressured rocks in many geologically young basins. Presumably, similar generation depth-pressure relationships existed earlier in many old basins. Thus, the geochemists have pointed out that we must know more about pressures than merely origins of abnormal pressures if we are to effectively trace petroleum from its source rocks to its sites of current entrapment.
Figures 1-16
TextInasmuch as there may be a wide range of reader prior knowledge regarding subsurface fluid pressures, this section is included to accommodate those with limited experience. More experienced readers may find it convenient to proceed directly from here to the next section. Readers desiring more illustrations of the basic concepts of subsurface pressures are referred to Amoco Geological Research Report M76-G-16 (Powley, 1976). Pressure is the force per unit area which fluids (liquids and gases) exert on the surface of any solid which they contact. Pressure exists at every point in a fluid at rest. The magnitude of the pressure is proportional to the depth below the surface; i.e., the pressure is the same at all points at the same level within a single fluid at rest. Also, the pressure at any depth is proportional to the density of the fluid (Figure 1). The pressure in a fluid at rest is independent of the shape of the containing vessel and is the same whether the vessel contains a fluid only or contains a fluid and a quantity of solids in grain-to-grain contact; i.e., not a suspension. Thus, in the earth, the pressure in a subsurface fluid is independent of the shape and size of the rock pores but is dependent upon the density of the fluid and upon the depth below its surface (Figure 2). In the earth, the datum water surface usually cannot be seen. However, pressure calculations commonly indicate that the rock pores are fluid-filled and interconnected from the top of the free water in the soil down to at least intermediate depths. Inasmuch as the soil water surface is usually only a few inches to a few feet below the topographic surface, it has become common practice to consider the free water surface and the topographic surface to be the same. In marine areas, the free water surface is considered to be mean sea level. The pressure previously discussed is that caused by the weight of a free-standing fluid column without any external pressure being applied. If any external pressure is applied to any confined fluid .at rest, the pressure at every point within the fluid is increased by the amount of the external pressure. This statement is known as Pascal’s Principle, after the French philosopher who first clearly expressed it. An example of a confined fluid is the fluid below a piston in a closed cylinder. The pressure in the fluid increases as external pressure is applied and returns to normal when the pressure is removed. Within the confined fluid, the rate of increase in pressure downward is the same with or without an external pressure (Figure 3). In geology, the counterpart to the piston and cylinder walls previously shown is any combination of rock layers and interfaces which completely enclose a body of fluid-bearing rock in a low-permeability envelope. The low-permeability envelope is usually referred to as a seal. A seal is usually thin with respect to both thickness and lateral extent of the enclosed rock body. An abnormally pressured rock body is like a huge bottle. It has a thin, essentially impermeable outer seal and an internal volume which exhibits effective hydraulic communication. The interval rate of increase in pressure with increasing depth within the internal volume is in direct accordance with the density of the internal fluids (Figure 4). The fluid pressures in the internal volume may be greater than, equal to, or less than the pressures in the fluids in the rocks outside of the seal. The magnitude of the internal fluid pressure is dependent on how much of the weight of the superincumbent rock column is borne by the fluids in the enclosed body and how much of the weight is borne by the rock matrix in the enclosed body. The fluid pressure below the top seal at the shallowest point in the enclosed rock body can range from zero, where the rock matrix bears all of the weight of the superincumbent rock, to about l psi/ft thickness of overlying rock if the enclosed rock matrix bears none of the weight of the superincumbent rock load (Figure 5). The Keyes Field in northwestern Oklahoma is illustrative of the case in which the rock matrix at the base of each of the two top seals bears the entire weight of the overburden, so the fluid pressures start from zero at these levels. All of the fluid pressures are markedly less than the normal +/- 45 psi/l00 ft from the surface, so the pressures in the Keyes Field, except those in the shallow beds above the uppermost seal, are termed underpressures (Figure 6). The Carpathian Basin in Hungary is an example of a rock load,being partially borne by the fluids below a seal. The fluid pressures are normal from the surface down to the base of the Pliocene clastics but are greater than normal below a thick series of lava flows which separate the Pliocene clastics from the Miocene clastics. Wells drilled on the northern shelf penetrate the normally-pressured Pliocene clastics, the seal, and the subseal high-pressured Miocene formations, whereas wells drilled in the southern basin usually penetrate only normally-pressured Pliocene clastics. The interval rate of pressure increase with depth in the Miocene section is the same as the rate of change in the normally pressured Pliocene section (Figure 7). This figure and the previous figure illustrating the Keyes Field demonstrate the field applicability of Pascal’s Principle. Pressures which are less than can be attributed to a free-standing water column to the surface were termed underpressures during the discussion of the Keyes Field. Likewise, pressures which are greater than can be attributed to a free-standing water column to the surface are termed overpressures. Underpressures and overpressures together comprise the well-known classification, abnormal pressures (Figure 8). Overpressures develop when there is an excess of pore fluids over available pore space. The state of volume imbalance may be due to pore space shrinkage or to pore fluid expansion (Figure 9). Most of the origins suggested in the geological literature involve pore space reduction by extensive mechanical collapse of the rock matrix under conditions of increased depth of burial. The rock collapse theories may be applicable in regions of very incompetent rock, like the shallow gumbo shales in the North Sea Basin, but are not acceptable in regions of competent rock like the Uinta, Green River, and Anadarko basins, the Grand Banks, the basal Jurassic sands in Mississippi, and the clastics in much of the Gulf Coast Basin. For instance, laboratory “rock squeezing” experiments on overpressured Gulf Coast shales indicate that those shales have many of the strength characteristics of limestone; hardly a low strength material (Figure 10). The first widely acceptable origin for most of the abnormal pressures encountered in wells was suggested by Barker in 1972, and expanded upon by Bradley in 1973, 1975, and 1976. It involves creation of overpressures by thermal expansion of pore fluids as pore fluids become warmer under conditions of deeper burial and creation of underpressures by thermal contraction of pore fluids resultant mainly from removal of cover by erosion. The Barker-Bradley proposal is based on considering a sealed rock body to be an essentially constant-volume vessel similar to a high-pressure boiler. As the temperature of a constrained volume of fresh water is increased, the pressure will increase at about 125 psi/oF of temperature change. Pressure in a saturated brine will change approximately 110 psi/oF of temperature change under the same conditions. If these conditions are applied to a geological model involving 1000 ft of increase in depth of burial, moderately salty water in a confined rock body and a geothermal gradient of 1.75°F/100 ft, the increase in pressure due to thermal expansion will be 2048 psi. If the rate of subsurface pressure buildup is in the order of 2000 psi per each 1000 ft of additional burial, the pressures would quickly become excessive and the confined fluids would burst through their seal by natural hydraulic fracturing. The internal pressure would then be able to blow down to some lower pressure. The fact that overpressures and underpressures are so common indicates that the fractures self-seal in some manner when the pressures in sealed-off rock bodies change sufficiently. Thus, it seems likely that the pressures in a sealed-off rock body undergoing continuous temperature increase through progressive burial are in a continuous cycle of buildup to fracture pressure, then fracture of the seal, followed by pressure drop, fracture healing and then buildup of pressures again (Figure 11). It is likely that pressure release by fracturing is localized at the shallowest depth of burial of overpressured rock masses. For illustration purposes, consider an overpressured rock mass at 15,000 ft depth under a 200-ft-thick seal (Figures 12, 13, and 14). The fluid pressure above the seal is 6882 psi, and 11,310 psi below the seal. Let there be a local upbulge of the top of the overpressured mass to a depth of 10,000 ft. The pressure differential across the seal remains the same (Pascal’s Principle). The overpressured fluids could vent themselves by natural hydraulic fracturing when the pressure is great enough to overcome the horizontal rock stress plus the tensile strength of the rock, plus overcome the fluid pressure in the formation being invaded. The horizontal stress ratio used was taken from Anderson, et al. (1973), and for the tensile strength figure it is assumed that the seal is indurated shale. The pressure below the seal at its shallowest depth (9000 psi at 10,000 ft) is greater than the pressure required to induce natural hydraulic fractures (8629 psi at 9800 ft), so fracturing would occur. However, at the regional depth of 15,000 ft, the pressure below the seal (11,325 psi) does not exceed the pressure required to induce natural hydraulic fracturing (12,904 psi) at 14,800 ft, so fracturing would not occur at that depth. This model demonstrates that venting of overpressures preferentially occurs at the point of shallowest depth of burial of an overpressured rock mass. Likewise, any hydraulic fracture venting of fluids from a normally pressured rock mass into an underlying underpressured rock mass will preferentially occur at the point of shallowest depth of burial of the underpressured rocks because the rock stresses are least there. Large reductions in pressure may be accomplished by the release of very small quantities of water. To depressure a 1000-ft-thick rock body with 10% porosity by 1000 psi requires the release of only 9.6/in3 water/in2 top surface. A square mile of rock, 1000 ft thick, 10% porosity, would have to yield only 6200 barrels of water to be depressured by 1000 psi (Figure 15). Most of the discussions to this point have dealt with pressures in individual wells or in local areas. When interpretations are extended from well to well over large areas, it is generally easier to deal in terms of potentiometric surfaces than with pressures in psi and pressure-depth ratios. A potentiometric surface is the elevation of the upper free surface of a fluid, generally at rest. In subsurface geology, the potentiometric surface for an aquifer is the elevation to which a free-standing fluid column of some specific density would rise if free to do so in a well penetrating only that aquifer. In normally pressured rocks the potentiometric surface of formation water corresponds to a “smoothed” topographic surface. In overpressured rocks, the potentiometric surface is above the topographic surface and in underpressured rocks the potentiometric surface is below the topographic surface. Calculations of potentiometric surfaces derived from elevations and measured pressures data are highly vulnerable to error if the fluid densities values used in the calculations do not correspond with the densities of the fluids in the aquifer. Figure 16 portrays calculations of a potentiometric surface applicable to the Basal Quartz formation in the Lanaway area of Alberta, Canada. Note that if a water density of 46 psi/100 ft is used, the calculated potentiometric surface is horizontal; however, if a fresh water density value (43.3 psi/100 ft) is used, the calculated potentiometric surface is markedly tilted. If a water density of greater than 46 psi/100 ft is used, the calculated potentiometric surface will be tilted in the opposite direction.
Fortunately, selection of an appropriate water density for use in
potentiometric surface calculations is usually quite easy. If carefully
measured pressures in normally pressured formations at several depths in
wells in a single basin are plotted against depth, the resultant profile
in each basin usually portrays a strictly linear relationship. The
pressure-depth ratio may be different from basin to basin, but within
any single basin, the ratio usually is remarkably constant. This is
apparently due to some equalization process in nature such that water
salinity, water compressibility, water temperature, and work being done
on the system jointly reach a vertical and horizontal equilibrium
density balance in all normally pressured formations within each basin.
For instance, a pressure-potentiometric head conversion factor of 45 psi/100
ft from the surface is applicable in normally pressured rocks at all
depths in most Rocky Mountains basins and a 46.5 psi/100 ft
pressure/depth ratio is similarly applicable in normally pressured rocks
throughout the Gulf Coast Basin. The same factors may be used as
interval gradient values in abnormally pressured During
the 1950’s, an interpretive technique known as “hydrodynamic analysis”
was widely applied, mainly by the Petroleum Research Corporation, a
Denver based consulting company, in the Rocky Mountains states and in
western Canada. The technique was based on the assumption that there is
a component of fluid flow from all sites with high potentiometric
surfaces to all sites with lower potentiometric surfaces within the same
rock layer. The technique was developed into elegant mathematical
derivations of the velocity of steady rate flow between pressure control
sites. The velocity figures were commonly developed further to establish
minimum rates of dip which would be required to retain oil and gas on
structures. The principal shortcomings in the hydrodynamics rationale
was the failure to recognize that there is a close vertical and
horizontal interdependence of aquifers (as outlined in the foregoing
paragraph) and the failure to recognize that water bodies laterally
sealed off from each other in the same rock layer could have substantial
differences in potentiometric surfaces and thus lateral differences in
potentiometric surfaces could signify either flow or no flow. Also,
nearly all of the early practitioners of the hydrodynamics art used
fresh water densities in their calculations of potentiometric surfaces.
Inasmuch as very few subsurface formations contain pure fresh water,
almost all of the resultant Sources of Pressure DataTextThe pressures in fluids in subsurface formations are generally determined by measurements within wellbores which have penetrated those formations. Well log data may also be combined with empirically derived relationships to derive reasonably reliable indicated subsurface pressures. The art of measuring shut-in pressures in wells is in good order, and there are a variety of reliable pressure measurement tools available. Inasmuch as those measurements are regularly conducted under the supervision of Company drilling engineers, many of whom are available for consultation by readers of this report, there seems to be no necessity for compiling a “how to” section in this report. Overpressures have been known and studied in the Gulf Coast Basin for many years. Most of the techniques to safely drill and complete wells in overpressured formations now in use worldwide were developed in the Gulf Coast. One of the most significant techniques is the use of well logs to identify and quantify overpressures. The techniques now in use are modified from those introduced in a paper presented by Hottman and Johnson in 1965. They reported the coincidence of high fluid pressures in sands and lower-than-normal electrical resistivities and acoustic velocities in adjacent shales in the Gulf Coast Basin. Figure 17 demonstrates the same relationship in the Uinta Basin. The technique using electrical logs involves an empirically derived relationship between the resistivity of shales adjacent to sands with fluids at normal pressures and the resistivity of shales adjacent to sands with overpressured fluids. The resistivity values for shales are generally easy to read on electrical logs (Figure 18). The ratios of the resistivity of the shales in the normally pressured section to the resistivity of the shales in the overpressured section are plotted on a ratio comparison chart which yields a pressure/depth ratio value applicable to the resistivity ratio (Figure 19). The resistivity relationship varies from basin to basin so a separate chart must be compiled for each basin. Electrical well logs do not respond to underpressures and do not respond to overpressures until a threshold pressure/depth ratio value of 61 psi/100 ft of burial depth is exceeded. The
reader should follow through the example calculations on Figures
18, 19,
20, 21,
22, and 23
at this point to insure that the technique is understood. This example
calculation is somewhat misleading inasmuch as the accuracy obtained is
better than that which can be routinely derived from average quality
well logs. The importance of the foregoing well log interpretation
technique is that it is possible to construct pressure-depth profiles
for overpressured Several authors have noted that abnormally high pressures are frequently accompanied by higher-than-normal geothermal gradients. Interval geothermal gradients in overpressured rocks in which pressure/depth ratios are greater than a threshold value of about 75 psi/l00 ft of burial depth usually are about 1.4 times as great as the geothermal gradients in rocks of similar lithology in which the pressure/depth ratios are less than about 75 psi/l00 ft (Figure 24). Geothermal gradients are much more difficult to work with than electrical logs because there usually are only a few temperature measurements in each well. Despite the frustrations of basing interpretations on skimpy temperature data, pressure/depth graphs derived from a combination of electrical log data and temperature data can be quite accurate. Hottman and Johnson (1965) contended that porosity in shale is abnormally high relative to its depth if the fluid pressure is abnormally high. That statement led to a flood of measurements of porosity and density of Gulf Coast shales. Amoco measured dry bulk densities and porosities in shale from drill cuttings and cores from nearly 30 million linear feet of borehole intervals in 4000 wells in the Gulf Coast Basin during the 1960’s. In 1966 Rogers described how profiles of the density of shales were then being used by some oil companies to identify overpressured shales and to estimate pressures in adjacent sands in wells in the Gulf Coast Basin. The prevailing belief was that the magnitudes of pressures may be determined by measuring the deviations of the densities of shales in overpressured rocks from a normal density-depth trend. Within a few years the technique was generally abandoned because drillers had developed more reliable indicators of overpressures in drilling wells and, more importantly, because it was discovered that overpressures occur in association with both normal density and low density shales. Low density shales were found to be universally overpressured but normal density shales could be overpressured, normally pressured, or underpressured. Research Department Report No. F82-G-23 deals more extensively with the relation between pressures and shale densities in the Gulf Coast Basin. Sonic well logs and field seismic data may indicate overpressures by a reduction in interval velocities and may indicate underpressures by an increase in interval velocities relative to interval velocities in normally pressured rocks of similar lithologies. There is no minimum pressure/depth threshold value which must be exceeded for velocity response. Thus, it might appear that sonic well logs would be more valuable than electrical well logs in quantification of pressures; however, sonic logs also respond to fractures,wellbore rugosity, alteration of shale by wellbore fluids, and to changes in lithology, particularly to the degree of mineralization. The response to fractures may overwhelm the pressure effects to the extent that the first discerned sonic log response at a normal pressure to overpressure transition is at the top of open fractures in the overpressured rock mass. In many basins there is so much lithology induced “noise” that interval velocity/depth profiles are satisfactory indicators that overpressures or underpressures exist, but such profiles are not consistent enough from well to well to provide reliable quantitative pressure values.
Geology of Abnormal PressuresFigures 25-26Return to top.
TextIn most deep basins in the world there is a layered arrangement of at least two superimposed hydraulic systems (Figure 25). The shallowest hydraulic system generally extends from the surface down to about 9000 ft greatest historical depth of burial in normal geothermal gradient basins and to slightly greater depths in cool basins. There are a few remarkable deviations, like the central North Sea Basin, the South Papua Basin, and the Canadian Arctic Basin, where the base of the shallow system has apparently never been buried more than a few thousand feet. The shallow hydraulic systems are basin wide in extent and typically exhibit normal pressures. The deeper hydraulic system usually is not basin wide in extent. It generally consists of a layer of individual compartments which are sealed off from each other and from the overlying system. In some basins, mainly onshore, there is a deeper, near normally pressured section (Figure 26). The compartmented layer, known as the Elisian Regime in eastern European literature, is generally in the sequence of rocks which were deposited during the mid-basin-life period of most rapid deposition in most basins. The underlying layer, where present, usually is in pre-basin shelf deposits and basement rock. The uppermost layer usually is in rocks which were deposited during the slowing rate of deposition late stage in basin filling. Recognition of the layered arrangement of hydraulic systems is generally quite easy. Only a few widely spaced, well documented deep wells with several tests run over perforated intervals are generally necessary to outline the overall arrangement of hydraulic systems in each basin. However, in some young, foreign basins and in the Copper River Basin in Alaska, fluidized rock material, mainly shale, and high pressure water with minor hydrocarbons are being locally ejected upward from subsurface overpressured compartments, through overlying normally pressured rocks and venting at the surface. Mud volcanoes may be built up at the vent sites. The rising, high-pressured mixture may pressure-up any shallow, permeable beds encountered, thereby locally complicating recognition of the layered arrangement of hydraulic systems. The individual compartments in the compartmented layer may be very extensive, as in some of the Rocky Mountains basins, or may be only a few miles across, as in the Gulf Coast Basin. The pressures within the compartments are usually markedly overpressured or underpressured relative to the pressures in both the shallower and deeper hydraulic systems. The compartmented hydraulic systems in geologically young basins are almost universally overpressured and are underpressured in most old basins. Thus, it appears that the compartments have an amazing longevity as they undergo a continuum from overpressures through normal appearing pressures to underpressures as their host basins progress from deposition, to quiescence, to basin uplift and erosion. In
those basins with three layers of hydraulic systems, the boundary
between the middle compartmented layer and the underlying layer usually
follows a single stratigraphic horizon. For instance, the basal boundary
of the compartmented section in the central Powder River Basin appears
everywhere to be within the thin Cretaceous Fuson shale. However, the
top of the compartmented layer is in many basins more complicated. It
(1) tends to follow an irregular sands-over-massive-shale boundary in
the Gulf Coast and Niger Delta basins, (2) it follows thin evaporites in
many onshore European and southwestern U.S. basins, and (3) it follows
horizontal or gently dipping planes which cut indiscriminately across
structures, facies, formations, and geological time horizons in the
northern Cook Inlet Basin, in the Alberta Basin, in the Anadarko Basin,
and in many Rocky Mountains basins (Figure 26). Those top surfaces which
do not follow a specific stratigraphic horizon are generally restricted
to clastics-dominated Planar seals may occur within, as well as on the top of, the compartmented layer. For instance, the shallowest seal in the Mill Creek Graben in southern Oklahoma is everywhere within the thin Marmaton shale; the next deeper seal is horizontal (-10,400 to -11,500 ft elevation), cuts through many Paleozoic formations across the graben and even extends, at the same elevation, across the adjacent Ardmore Basin. No deeper seals have been encountered in the graben or in the Ardmore Basin. Earlier in this report it was pointed out that the individual compartments in the compartmented layer are like huge bottles with thin bounding seals and huge fluid-communicating internal volumes. Seals are particularly annoying to work with because they do not have unique 1ithologic properties other than extremely low permeability. In the absence of unique lithologic properties, recognition must be accomplished from indirect evidence, such as well log indicators, measured pressures in local reservoirs encased in seal rock, and often only from the requirement that they must be there separating reservoirs which, from measured pressure data, are obviously hydraulically separated from each other. The transition of pressures across the thickness of top seals is linear wherever data have been obtained (Figure 24). No data have been accumulated to determine the patterns of pressures within lateral seals. In some areas, seals may be recognized by calcite and/or silica mineralization, probably resultant from dissolved minerals being precipitated as water seeps through the seals. The mineral infill of porosity and fractures may be so readily recognizable that it becomes an identifier of present or past seals. For instance, calcite infill is so ubiquitous in seals in southwestern Louisiana that it has been given the name “AI’s Cap,” named for Al Boatman, a local geologist, who first publicly drew attention to the phenomenon there. Silica infill may be recognizable on the basis of drastically reduced rates of drilling penetration across a seal. For instance, it took 24 hours to cut a 60-ft core in a silica-enriched seal in chalk in the Shell-Esso 30/6-2 well in the North Sea. Chalk normally cores very rapidly. Top
seals in clastics-dominated Lateral seals appear to be generally vertical or very nearly vertical. They range in thickness from less than one eighth of a mile (within the distance between wells on 10-acre spacing) to about six miles, with the majority being about one eighth of a mile in width. They tend to be quite straight, suggesting that they may tend to follow fault trends. There have not been any satisfactory suggested geochemical mechanisms which could create impermeable walls over thousands of feet of vertical extent through rocks of many lithologies. Where wells have penetrated lateral seals, the rocks have generally been found to be slightly fractured and the fractures infilled with calcite and/or silica. In a few localities some of the fractures are locally open and can yield limited oil and gas production. The
rocks in the internal volumes within the compartments, like the seals,
do not have a unique lithology. The most unique property is the
pervasiveness of fractures observed in cores and indirectly indicated by
the apparent hydraulic continuity; i.e., reservoir to reservoir
continuity of interval pressure-depth profiles within the internal
volumes. A few authors, most notably Narr and Currie (1982), have
attempted to explain a genetic mechanism for the fractures; however,
none of the explanations to date have been particularly convincing. The
fractures in underpressured through slightly overpressured Cretaceous
rocks are generally nearly closed in most basins; however, they are
generally open enough to cause prominent reductions in interval sonic
velocities in overpressured rocks which display a pressure-depth ratio
greater than 67 psi/l00 ft from the surface in the Gulf Coast Basin. No
fracture-opening versus pressure-depth-ratio data have been assembled
from overpressured The fractures in the internal volume are, in a few areas, open enough to permit commercial-rate extraction of oil and gas even in the absence of significant matrix porosity and permeability. However, the distribution of open fractures is generally not uniform enough to allow field development without a substantial proportion of dry holes unless the fracture porosity is augmented with matrix porosity and permeability within the internal volume rocks. The matrix rocks, in different areas, may exhibit remarkably different porosity values. For instance, sandstone porosities are in the 20-35% range in the overpressured Cretaceous Tuscaloosa sand reservoir in the False River field in Louisiana and are generally much less than 10% in the Paleozoic Goddard sand reservoir in the Fletcher field in Oklahoma at approximately the same depth and pressure.
Basin FluidsFigures 27-34
TextThe four most important recent developments in basin fluids concepts are (1) the recognition that there probably is much less lateral movement of pore fluids than was envisioned in the heyday of hydrodynamics, (2) the recognition that vertical migration of pore fluids is more prevalent than earlier recognized, (3) the recognition of the ubiquity of pressure compartments and their effects on the movement of all pore fluids and (4) underground hydraulic fracturing of rocks now appears to be an important fluids transport mechanism. Combination of the foregoing concepts provides a speculative indication of how petroleum starts its path from its source rocks towards its sites of entrapment, providing oil and gas takes the same migratory path as water. Currently popular geochemical concepts place the depth to petroleum generating formations in many basins in the general 10,000 to 16,000 ft interval at the time of historical greatest depth of burial. That depth range usually places the generation of most oil and gas within or, in a few basins, below the compartmented hydraulic system, which probably was overpressured at that time. The oil and gas generated within the overpressured compartments apparently makes its way upward through fractures within each compartment and may be trapped against the external pressure seal or may be ejected by intermittent natural hydraulic fracturing at the localities of the shallowest depth of burial of each overpressured compartment. The mixed gas-oil-water fracturing fluid probably bursts into the closest available, lower-pressured, but not necessarily normally pressured, permeable bed or fault and loses its drive. There is such a disproportionately large amount of oil and gas in traps in the closest lower-pressured permeable reservoir rocks above overpressured rock masses in proximity to present and/or past local areas of shallowest depth of burial of those overpressured rock masses in such diverse areas as the Cook Inlet, Gulf Coast, Niger Delta, and Caspian Sea basins that the interpreted hydraulic fracture breakout process appears to be essentially correct. The point of shallowest burial may be the arched top of an anticline, of a dome, of a drape fold over a buried hill or reef, of a tilted fault block, of the top of a stack of overthrusts, or the top of the shale sheath peripheral to a salt dome. It appears that all potential traps located within about one mile, upward from and horizontally from the point of local shallowest depth of burial of the top (base of the top seal) of an overpressured section should be explored (Figures 27, 28, 29, and 30). The foregoing is applicable where the shallowest depth of burial is due to an upbulge of the top of an overpressured section. However, in regions of great topographic relief, the shallowest depth of burial may be due to a local very low surface elevation. In that situation, hydraulic fracture breakout also occurs at the location of the shallowest depth of burial; however, there is no buried local upbulge to pre-collect oil or gas there. The Transylvanian Basin may be an example of that situation. The top seal of the overpressured section is horizontal and Romanian geologists have reported the ascent of hot, medium-salinity water with minor oil and gas in a few localities beneath major river valleys, but they have not reported similar ascending water plumes below the adjacent high plateaus. Around 1970 Bobby Newton, then the Region Geologist in New Orleans, attempted to categorize the localities of large oil and gas pools in southern Louisiana relative to their pressure environments. His system categorized pressures by relations to stratigraphy; i.e., pressure boundaries rising across stratigraphy, parallel to stratigraphy, or dropping across stratigraphy. Newton’s descriptive categories, which required precise correlation of beds, were difficult to recognize and difficult to work with, particularly during the wildcatting and early field development stage, so the system was not adopted; however, his diagrams indicate that all of the major pools studied are in very close proximity to local points of shallowest depths of burial of the overpressured hydraulic system. Figures 31, 32, 33, and 34 are from a seminar prepared by Newton in support of his descriptive category system. Those readers who remember the Newton seminar may note that wildcat wells would be located at the same sites if the Newton descriptive system is used or if the proximity-to-the-shallowest-depth-of-burial genetic concept is adhered to. Some oil and gas will escape entrapment in proximity to the regions of fracture breakout and may move far into the shallow hydraulic system. It may become trapped in shallow formations and, with luck, will escape degradation by water-borne bacteria. Conventional updip migration and trap concepts explain the occurrence of much of the “escaped” oil and gas. Oil and gas has also accumulated in abundance within the internal volumes of abnormally pressured compartments. Accumulations may be in traps within the internal volume or may be trapped within or against the bounding seals. Many of the pools located within the internal volumes of abnormally pressured compartments have tended to be rather small in the Gulf Coast Basin, probably because the individual compartments are small and because the reservoir sands are thin and discontinuous. All of the internal sands are oil-filled in the Altamont-Bluebell overpressured compartment in the Uinta Basin; all of the internal sands are gas filled in the Blanco underpressured compartment in the San Juan Basin; and all of the sands in the deep Wind River Basin overpressured compartment appear to be gas filled. Over one billion barrels of oil have been produced from Paleozoic reservoirs within the internal volume and within the top seal of the underpressured compartment in the Seminole Sag, a small graben adjacent to the Arkoma Basin in southern Oklahoma. The trapped-against seals accumulations may be at the highest internal elevation regions where the oil and gas awaits release by hydraulic fracturing or may be in regionally permeable beds where they are cut by bounding seals. The oil and gas pool in the fractured, overpressured Monterey shale reservoir on the Lost Hills Anticline in the San Joaquin Basin appears to be an example of oil and gas in a pending-fracture-release pool. The large, underpressured Viking oil and gas pools trending from the Oyen-Sedalia area through the Provost, Killam, Bruce, Beaverhill Lake, Fort Saskatchewan, Fairydell-Bon Accord, Westlock and Judy Creek fields in the Alberta Basin provide an example of entrapment against a bounding seal. Those fields are in a 350-miles-long megatrap where the southwestward dipping Viking sand is regionally cut by a horizontal seal at about sea level elevation (see Figure 50). An important extra benefit from petroleum remaining within abnormally pressured compartments, particularly in deeply eroded regions, is that oil pools are protected from contact with bacteria-bearing meteoric waters. For instance, the regional pressure seal in the Castile-Salado evaporites has protected the shallow, underpressured giant oil pools in West Texas from being bacterially degraded. The only bacterially degraded oil in the entire West Texas-southeastern New Mexico area is in above-the-seal beds, mainly near Santa Rosa, New Mexico. The foregoing generalization applies to conditions prior to the intrusion of man. Injection of bacteria bearing water during waterflooding has resulted in local bacterial degradation of oil in some pools. Many
oil and gas pools within abnormally pressured compartments exhibit
isolated ponds of water well above the pools’ water tables, probably
because there was not enough vigor to fluid movements within sealed-off
compartments to sweep all of the water out of the oil and gas pools. An
example is provided by the Recluse - Bell Creek underpressured
compartment in the northern Powder River Basin. In that compartment, the
pool to pool interval pressure/depth ratio in the Muddy Formation is 33
psi/100 ft; i.e., the pool to pool pressure transmitting medium has the
density of oil, rather than water. Thus a very large, continuous oil
pool is indicated. However, there are large ponds of water which
apparently have been prevented, by tight areas and local shaleouts in
the Muddy sand, from moving downdip to the main water body. Thus the
entire area is a huge oil pool with internal local ponds of water.
Another example, of more direct interest to Amoco, is provided by the
underpressured Wolfcampian Bough “C” limestone in eastern New Mexico.
During the late 1950’s and early 1960’s, six widely separated oil pools
were discovered. The pool to pool interval pressure/depth ratio was 33.6
psi/l00 ft; a density figure compatible with the oil in the six pools.
Thus a very large, continuous oil pool was indicated. Amoco drilled an
inter-pool wildcat, the State “DO” No.1, in a slight Oil and gas may have been generated below the compartmented layer in some basins. For instance, the sub-Fuson pays in the central Powder River Basin probably were generated below and have remained below the compartmented layer. The oi1 and gas appears to have been unaffected by the overlying compartments, except that the deep section may have been effectively shielded from surface influences like meteoric water drives. Despite the obvious advantage of not being subject to strong water flushes, the hydraulic layer below the compartmented layer has not been found productive in many basins. Some of the low productivity is probably due to limited deep drilling.
Ruptured CompartmentsFigures 35-37
Return to top.TextUp to now we have been dealing with compartments in which the bounding seals have been continuously intact since their formation or have undergone brief episodes of hydraulic fracturing and subsequent healing. There are several recognized compartments in which the bounding seals have been permanently ruptured by erosion or faulting or were breached by hydraulic fracturing without subsequent healing. The remaining seal segments apparently are still as impervious to gas, oil, and water as they were when the seals were complete; therefore recognition of seal segments is very important in petroleum exploration. Pressures within a newly ruptured compartment will progressively change toward equilibrium with the pressures in the external water through fluid leakage into or out of the compartment at the point of rupture. When pressure equilibrium is reached at the elevation of the rupture, there is no pressure differential to move fluids farther. If the rupture is large, or if the adjacent rocks are very permeable, there may continue to be gravitationally driven fluid movement; i.e., water may trickle into a gas filled compartment and the gas may bubble out even if the water and gas pressures are equal. During the in-or-out movement of fluids, the internal pressure at the elevation of the rupture remains equivalent to the external water pressure; downdip gas remains underpressured relative to the pressures in the external water and the updip gas remains overpressured relative to the pressures in the external water (Figure 35). If the rupture is very small, or if the adjacent rocks have low permeability, the internal and external fluid systems may laterally coexist for a long time after attainment of pressure equilibrium. If the external pressure is decreased, generally through progressive erosion of cover, the fluids within the compartment will seep out to maintain pressure equilibrium. Figure 36 portrays the pressure-depth profiles which would be compatible with petroleum trapped within a ruptured compartment under the pressure conditions imposed by different locations of the rupture. Compartments in which the bounding seals were breached by hydraulic fracturing at their shallowest depths of burial without subsequent healing may still contain huge amounts of oil and gas. The giant Milk River gas field in Alberta may be of this type. It fills an underpressured compartment with an internal gas pressure of 625 psi at its updip terminus. The adjacent external water pressure is also 625 psi. Figure 37 portrays the pressures at Milk River if PGl, the pressure in the gas, equals PWl, the pressure in the adjacent updip water. Note that the compartment is normally pressured at its updip leak point but, because gas is less dense than the external water, the gas pool is underpressured relative to the external water in its full downdip extent. The better known, underpressured, giant Medrano oil pool on the Cement Anticline in Oklahoma is of the same type. The Medrano pool is ruptured underground at its updip terminus. It has continued to leak oil as erosion has progressively removed cover and thereby reduced the external normal pressures. The leakage plume over this field has been extensively used by promoters of geological and geophysical techniques which directly sense the hydrocarbon plume or sense the chemical changes in rocks due to the continued presence of seepage oil. A compartment may be breached by erosion, generally at the pre-breaching site of the shallowest depth of burial of the upper seal. When this occurs, any oil or gas awaiting hydraulic fracture breakout would suddenly be exposed to the atmosphere. The giant Athabasca tar sands deposit in Alberta probably had this history. The deposit is at the northeastern updip terminus of the sub-Viking pressure compartment which extends over most of the Alberta Basin. Inasmuch as the water-bearing formations contain salty water all the way up to the outcrops, the compartment, now underpressured except at the rupture area, may have been overpressured until erosional breaching. The giant Oklahoma City Field apparently had a similar early history. That field is located at the updip terminus of the lower (sub-Meramec) tier of compartments in the Anadarko Basin compartmented layer. The compartment was breached by early Pennsylvanian erosion. A thin, but extensive tarry layer at the unconformity attests to the pre-erosion presence of a large oil pool. The unconformity was reburied by thousands of feet of Pennsylvanian and younger rocks. The Cherokee shale, overlying the buried unconformity, resealed the compartment and a trend of new oil pools from Criner-Payne, through Oklahoma City and West Edmond was established along the updip edge of the resealed compartment. Small pools continue to be discovered along the updip boundary of that compartment. Rupture
of a seal downdip from the updip terminus of a dipping compartment will
lead to pressure equalization at elevation of the point of rupture but,
if the rupture is small or if the adjacent rocks have low permeability,
long columns of oil or gas may remain within the compartment, both updip
and downdip from the point of rupture (Figure 35). The internal
pressure-elevation profile will The evidence for ruptured seals in the tight gas sand areas is not unassailable. It is possible that some of those compartments have not been ruptured; rather they are fully sealed but are in the “midlife identity crisis” period when compartments are passing from early basin-life overpressures to late basin-life underpressures. A large rupture in a compartment seal may lead to a normally pressured water column within a compartment, not only downdip from the point of rupture, but also updip to the base of any oil or gas column trapped against the remaining updip seal segment. Thus, any wells drilled into the water-bearing sector of the compartment would not yield an abnormal pressure indicator of the presence of a compartment. It would be easy to overlook the petroleum trapping potential of the unruptured updip segment of the compartment seal. There is no current geological or geophysical method known to the author for recognition of such seal segments except by inference. For instance, a trend of pools at the same elevation, an unusually straight line trend of pools, superimposed “stratigraphic trap” pools, or even the apparent abutment of different salinity waters in apparently continuously permeable beds may spark intuitive interest and lead to recognition of the fundamental trapping mechanism while there is still time remaining and acreage available to wring a reward from the interpretation. The terms “point of pressure equalization” and “seal rupture,” used in the preceding paragraphs, may be misleading because they may create the impression that the internal-external pressure equalization path is necessarily quite short. In a few cases, the path from the internal volume of a compartment to the external normal pressure control is a very long distance, particularly if the equalization path extends from one compartment into, across and out of an adjacent compartment. For instance, the internal pressure at the base of the gas-filled Blanco pressure compartment in the central San Juan Basin appears to be controlled by the elevation of the Paleozoic rock outcrops in the Grand Canyon, slightly over 200 miles away. The intervening path is interpreted, on the basis of coincident elevations of potentiometric surfaces, to be through the underpressured Paleozoic formations in the Paradox Basin.
Mapping CompartmentsFigures 38-51
TextThe most fundamental elements of the petroleum geology of abnormal pressures and of the geology of compartments are the geology and the geometry of seals. In general, for petroleum exploration purposes, it is unimportant whether the pressures in a compartment are markedly abnormal or only slightly abnormal, whether the compartment encloses a thousand square miles or is only half that size, or whether a compartment contains Paleozoic and Mesozoic rocks or contains only Mesozoic rocks, but it is very important that the pattern of seals be recognized and understood and that the locations of seals crossing permeable beds be recognized and accurately mapped. The seals, not the whole compartments, trap or control the trapping of oil and gas. For
mapping purposes, seals may be considered to be subsurface layers or
surfaces which are recognizable on both regional and local scales, may
be correlated from place to place and may be mapped like other
subsurface layers or surfaces. Top seals and bottom seals are like
“thick” unconformities; i.e., they may cut across or may parallel
depositional layers and are identifiable mainly on the basis of the
differential properties of the shallower and deeper When
commencing a study of subsurface pressures in a previously unstudied
basin, an investigator should first determine if, and approximately
where, abnormal pressures have been encountered in wells within the area
of study. Most government field-development regulatory bodies in the
United States and Canada require sworn-to public disclosure of the
discovery shut-in pressures in all productive pools; so this data source
is generally the best place to start. In most domestic basins that data
source is sufficient to roughly outline the main pressure compartments,
if present. In those Company locations which have old potentiometric
surface The
next step is to construct work The
work The next step is only a slight variation of the procedure well known to most experienced subsurface geologists; i.e., examine every indicated updip interruption in carrier bed continuity to determine if a stratigraphic trap type or fault type play may be made. Figures 39, 40, 41, 42, 43, and 44 portray the suggested steps using the Anadarko Basin as the illustrative area of study. Figures 39, 40, and 41 are pressure-elevation profiles of discovery pressures in individual pools, using data derived mainly from state government regulatory sources. Note the generally clean separation of pressure profiles, hence leading to an early recognition of the reality and approximate locations of major pressure compartments. Figure 42 shows the approximate outline of the individual compartments in the combined Morrow and Springer formations. The structure map of the Morrow Formation (Figure 43) is referred to next to determine where interruptions in updip carrier bed continuity are indicated and thus where infill data are required. Combination of Figures 42 and 43 (Figure 44) portrays several updip compartment boundaries and corners, which are prospective. Many of those sites have been tested; some have been productive for years, and one is currently (1984) being developed; however, a few prospective updip corners are still untested and are currently being studied further by the Denver Region. The Anadarko example may be misleadingly simple, inasmuch as the pressure control from fields is adequate to outline most of the pressure compartments. The more usual situation is that there are only a few pools in each compartment (Figure 45); so the investigator is faced with a large fleshing-out job using data from wireline tests, drillstem tests, echometer readings, and even densities of mud required to maintain reasonably balanced drilling. An even higher order of difficulty is presented by basins with few wells and few-to-no oil and gas pools. For instance, the compartmented layer is readily recognizable in wells in all of the coastal and offshore basins from the Gulf of Alaska to the Eel River Basin in California; however, there are only about 10 wells per basin so there are not enough data to permit adequate mapping of compartments there.
Pressure-depth profiles using only reliable pre-drawdown shut-in
pressures in several formations in individual fields or wells may
facilitate recognition of the vertical arrangement of pressure
compartments. The investigator should correct all within-pay pressures
for buoyancy to pressures at or below the bottom water surface.
Figure
46 illustrates the error which could be introduced by using a within-pay
pressure, particularly if that pressure was measured high up in a long
oil or gas column. Figure 47 portrays pressures measured at several
depths in an individual field. The profile indicates one abnormally
pressured compartment and the approximate location of the top seal. That
information is sufficient to get an investigation underway. Figures
48
and 49 portray the follow-up steps; i.e., gather more data and then
construct Another
“getting started” technique .is to construct regional
Future WorkThis report is intended to provide a technical and conceptual background for using pressure data in developing and modifying exploration plays. The application techniques are sufficiently developed that the Regions may take over most pressure related applications and Geological Research may shift farther into a support-when-needed role on the subject. There is need for further development of geophysical techniques for identification and quantification of abnormal pressures. Also, further understanding of seals might be worthwhile, but it is not clear that new work by the Research Center is required now. If we wait until the Regions have worked with seals, research could be in response to real needs, not just to anticipated needs.
ReferencesAlliquander, O., 1973, High pressures, temperatures plague deep drilling in Hungary: Oil and Gas Jour., v. 71, no. 21 (May 21), p. 97-100. Anderson, R.A., Ingram, D.S., and Zanier, A.M., 1973, Determining fracture pressure gradients from well logs: Jour. Petrol. Tech., v. 25, p. 1259-1268. Barker, C., 1972, Aquathermal pressuring, role of temperature in development of abnormal pressure zones: AAPG Bulletin, v. 56, p. 2068-2071. Bradley, J.S., 1973, Abnormal formation pressure: Amoco Geological Research Report F73-G-6, 33 p., 25 figures. Bradley, J.S., 1975, Abnormal formation pressure. AAPG Bulletin, v. 59, p. 957-973. Bradley, J.S., 1976, Abnormal formation pressure: Reply: AAPG Bulletin, v. 60, p. 1127-1128.
Coffin, R.C., 1925. Notes on the circulation of water in
the sands of Handin, J., and Hager, R.V., Jr., 1958, Experimental deformation of sedimentary rocks under confining pressure: Tests at high temperature: AAPG Bulletin, v. 42, p. 2892-2934. Hottman, C.E., and Johnson, R.K., 1965, Estimation of formation pressures from log-derived properties. Jour. Pet. Tech., v. 17, p. 717-722. Hubbert, M.K., 1940, The theory of ground water motion: Jour. Geo1., v. 48, p. 785-944. Hubbert, M. K., 1954, Entrapment of petroleum under hydrodynamic conditions: AAPG Bulletin, v. 37, p. 1954-2026. Illing, V.C., 1938, The origin of pressures in oil-pools: Science of Petroleum, Oxford Univ. Press, v. 6, p. 224-229. Narr, W., and Currie, J.B., 1982, Origin of fracture porosity - example from Altamont Field, Utah: AAPG Bulletin, v. 66, p. 1231-1247. Powley, D.E., 1976, Pressures, normal and abnormal: Amoco Geological Research Report M76-G-16, 11 p., 56 slides, 1 tape recording. Powley, D.E., 1982, The relationship of shale compaction to oil and gas pools in the Gulf Coast Basin: Amoco Geological Research Report F82-G-23, 13 p., 60 figures, Appendix 500 figures. Rogers, L., 1966, Shale-density log helps detect overpressure: Oil and Gas Journal, v. 64, no. 37, p. 126-130. Ronai, A., 1978, Hydrogeology of great sedimentary basins: Proceedings of the Budapest Conference, 1967: International Association of Hydrologic Sciences Publication no. 120, 829 p. Russell, W.L., 1956, Tilted fluid contacts in Mid-Continent region: AAPG Bulletin, v. 40, p. 2644-2668. Vers1uys, J., 1932, Factors involved in segregation of oil and gas from subterranean water: AAPG Bulletin, v. 16, p. 924-942.
AppendixAir standard and water standard (psi/100 ft) Densities (pressure gradient, salinity, mud weight, API gravity) Density vs. temperature and pressure for water and NaCl solutions Density of average natural gas versus depth Crude oil density versus temperature and pressure Determination of subsurface density and pressure gradient from stock-tank API gravity and GOR Depth correction to find true vertical depth of nonvertical boreholes |