Click
to article in PDF format.
GCTime-Lapse 4-D Technology: Reservoir Surveillance*
By
David H. Johnston1
Search and Discovery Article #40142 (2005)
Posted February 9, 2005
*Adapted from the Geophysical Corner column in AAPG Explorer, December, 2004, entitled "4-D Gives Reservoir Surveillance,” and prepared by the author. Appreciation is expressed to the author, as well as to Alistar R. Brown, editor of Geophysical Corner, and Larry Nation, AAPG Communications Director, for their support of this online version.
1ExxonMobil Exploration Company, Houston, Texas ([email protected])
Reservoir surveillance during production is a key to meeting goals of reduced
operating costs and maximized recovery. Differences between actual and predicted
performance are typically used
to update the reservoir's geological model and to
revise the depletion strategy. The changes in reservoir fluid saturation,
pressure, and temperature that occur during production also induce changes in
the reservoir acoustic properties of rocks that under favorable conditions may
be detected by seismic methods.
The key to seismic reservoir surveillance is the concept of differential imaging using time-lapse, or 4-D measurements. Time-lapse seismic methods are usually based on differences in seismic images that minimize lithologic variations and emphasize production effects. The concept is illustrated in Figure 1, where a base 3-D survey acquired before production is compared with a monitor 3-D survey acquired at a later time, dependent on the recovery process to be monitored.
The difference between the seismic surveys can then be interpreted in terms of the production-related changes in reservoir properties. Time-lapse seismic data have been shown to increase reserves and recovery by:
-
Locating bypassed and undrained reserves.
-
Optimizing infill well locations and flood patterns.
-
Improving reservoir characterization -- identifying reservoir compartmentalization and permeability pathways.
Four-D also can decrease operating costs by:
-
Reducing initial development well counts.
-
Optimizing phased developments using early field-wide surveillance data.
-
Reducing reservoir model uncertainty.
-
Reducing dry holes and targeting optimal completions.
-
As a result of these benefits, many oil companies are aggressively pursuing the application of time-lapse seismic data.
uGeneral StatementuFigure captionsuPhysical basisuSeismic repeatabilityu4-D acquisition, processingu4-D interpretation
uGeneral StatementuFigure captionsuPhysical basisuSeismic repeatabilityu4-D acquisition, processingu4-D interpretation
uGeneral StatementuFigure captionsuPhysical basisuSeismic repeatabilityu4-D acquisition, processingu4-D interpretation
uGeneral StatementuFigure captionsuPhysical basisuSeismic repeatabilityu4-D acquisition, processingu4-D interpretation
|
The Physical BasisSeismic velocity and density changes in a producing reservoir depend on rock type, fluid properties, and the depletion mechanism. Time-lapse seismic responses may be caused by:
Reservoir
factors that affect the seismic detectability of production changes can
be evaluated in order to determine which geological settings and
production processes are most suited for reservoir monitoring. Each
field is unique, and modeling of the seismic response to production,
based on reservoir flow simulation, is
The optimal times for repeat seismic surveys depend on detectability and the field's development and depletion plan. Planning for repeat surveys in the context of field surveillance will maximize the value of the data. Seismic RepeatabilityThe difference between two seismic surveys is not only sensitive to changes in reservoir rock properties but also to differences in acquisition and processing. As suggested in Figure 2, the chance of success for a 4-D project depends on both detectability and seismic repeatability. Some of the factors that affect repeatability include:
4-D Seismic Acquisition, ProcessingThe objective of 4-D seismic acquisition and processing is to minimize differences in the seismic data that are unrelated to production -- and to preserve and resolve those differences in the reservoir that are due to production. Four-D repeat survey acquisition attempts to match both the source and receiver positions and signatures of the baseline survey. Positional repeatability ensures the same raypaths for base and monitor surveys. Tolerance to geometry deviations depends on the complexity of the overburden; where there is rapid lateral change or anisotropy in the overburden, raypaths need to be more similar. A number of strategies have been developed to maximize acquisition repeatability for both land and marine data, and permanent monitoring systems -- such as the BP's installation at Valhall -- can result in high repeatability. While there is a large up-front cost associated with fixed receivers, these systems can permit the acquisition of lower-cost monitor surveys with short repeat intervals or "on demand."
Four-D processing is best described as co-processing or parallel processing of base and monitor surveys. This implies:
A key to
successful time-lapse processing is continual comparison of the base and
monitor surveys to ensure that repeatability is not being compromised.
Often, "fast track" data (e.g., decimated, post-stack migrated and/or
using parameters based on earlier processing) are
Also, the
objective to maximize repeatability may be at the expense of other
processing objectives, such as high-resolution imaging. As a result, it
is not uncommon that separate flows are 4-D InterpretationThe interpretation of time-lapse seismic differences in terms of reservoir changes requires integration of the data with detailed reservoir characterization, fluid flow simulation, petrophysics, and conventional reservoir surveillance data. Many companies use a model-based 4-D interpretation workflow, where seismic differences are compared to predicted differences based on seismic modeling of history-matched reservoir flow simulations. The interpretation process is one of comparing, contrasting, reconciling and validating these two images of the production process.
This
approach is
An example of 4-D interpretation is from the North Sea Jotun Field, where oil is being depleted through a strong natural water drive. Water sweep in the reservoir results in a 10-12 percent increase in the seismic impedance. Figure 3 compares the results of inverting the seismic difference acquired after three years of production to obtain impedance change with the oil saturation change predicted by the reservoir flow simulation. At this location, the simulator suggests that the reservoir is fully swept -- but the seismic data show that only one reservoir zone has been swept and that internal shales act as barriers or baffles to flow. This results in a flank rather than bottom water drive.
Infill or
sidetrack opportunities are found where there is no change in the
seismic data and where reservoir characterization suggests there is high
net-to-gross sand. As a result of the 4-D survey at Jotun, three
successful infill wells were drilled and a
Other
published 4-D case studies show that seismic data can image production
changes in a variety of geological settings and production scenarios,
including water and gas sweep, pressure changes and compaction, and
enhanced recovery. Further, 4-D interpretation is evolving toward a more
quantitative analysis of the data. By incorporating time-lapse shear
More predictive simulations will result in more efficient reservoir management.
|